https://userguides.robotical.io/ 2026-04-23T10:26:58+00:00 https://userguides.robotical.io/ https://userguides.robotical.io/_media/logo.svg text/html 2024-03-09T13:18:15+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/0_beforeyoubegin?rev=1709990295&do=diff For the smoothest, easiest build, we’d recommend using this online Build Guide alongside the printed paper one that came in your Marty’s box. While you’ll do fine with just the paper guide, this online guide has extra tips and details to make your build experience easier. text/html 2024-03-09T13:34:49+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/1_legs?rev=1709991289&do=diff Let's start with putting together Marty's Legs... [Servo Mount] [Hip/Knee Servo] [Servo Horn Screw] Take one of the blue Hip/Knee Servos and place it into the Servo Mount, securing it with a servo horn screw into the plastic - the video below shows this in detail. Do this four times with all four blue metal servos. When you’re done, put two assemblies aside and go on to the next step.Step 1‘J’other side text/html 2024-03-09T13:37:26+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/2_arms?rev=1709991446&do=diff [Arm/Eye Servo] [Side Panel] [M2 Nut] [M2x10mm Bolt] Attach a white Arm/Eye Servo to each Side Panel using two 2x10mm Bolts and 2mm Nuts for each one. This can be a bit fiddly, we find the easiest method is to use a finger, piece of tape or blu-tac to hold the M2 Nut in place as you get the Bolt lined up. If you’ve got tweezers, you can also do it backwards with the nut in the hole. text/html 2024-03-09T13:40:56+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/3_head?rev=1709991656&do=diff [Head Base] x1 [Power Cable] x1 Take the Head Base and the Power Cable. Poke the wires and the retaining nut through the rectangular hole. [Step 15 Assembly] x1 Press the socket gently into the circular hole. Tighten the retaining nut around the charging socket. Finger-tight will do just fine, this nut is just there to hold it in.Note: text/html 2024-03-09T13:41:29+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/4_putting-it-together?rev=1709991689&do=diff Firstly, check that you've got all the right bits for your Robot built — Two legs, both halves of the Head, and two Arm Assemblies. Also take the time now to check you've got both legs built correctly, as it's harder to fix later! If they don't lookLegs text/html 2024-03-09T13:42:20+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/5_connecting-electronics?rev=1709991740&do=diff [Sticker Sheet] x1 [Step 19 Assembly] x1 Now you've connected both legs, carefully slot the bottom ridge of the Arm Assemblies into the Head Base, to clip them in place. You might find it easier to leave the arms off until you’ve put the electronics in - but it’s very easy to take them off again.Step 21.+5VMSIG text/html 2024-03-09T13:49:09+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/6_next-steps?rev=1709992149&do=diff [M2.5 Nut] x2 [M2.5x8mm Bolt] x2 With all your electronics connected, swing the face over (making sure the Side Panel flanges end up inside the head), and screw it shut using 2 x 2.5mm Nuts and Bolts in each corner where the Head Base and Face meet. [Sticker Sheet] x1 Personalise your Marty! Just before you move on to connecting Marty to your WiFi and calibration, you need to make your Marty look the part. From the Sticker Sheet you can give Marty eyebrows and eyesGo To the WiFi Setup G… text/html 2024-03-11T12:51:20+00:00 Anonymous (anonymous@undisclosed.example.com) https://userguides.robotical.io/martyv1/buildguide/start?rev=1710161480&do=diff